AvantaPure 269 Spécifications télécharger pdf (Page 9)

960 Avantapure Control

Figure 6

Programming

This section covers all aspects of programming the control.

The control is shipped from the factory with default values for

Hardness and Capacity. These default values will result in a

system capacity of

100 gallons (1 cubic meter). While the control will operate

with these values, they should be changed to meet the actual

operating conditions.

Note that some parameters have a single unit of measure option

such as the Rinse Time which is only entered in minutes. Other

parameters have dual units such as Salt Amount which can be

entered in pounds or kilograms. To select which units are active,

look for a comment in the NOTES column of Table 1 and Table

2. It will reference another parameter that selects which units are

active. For example, Parameter P12 (Table 3) selects U.S. units if

it is set to “0” and metric if it is set to “1.”

Level I Parameters (Table 1)

Level I Parameters are identied as those that have an LED

indicator on the front panel. The green indicator illuminates

next to the name of the active control setting. The end user has

access to all of these parameters. In general, pressing the down

arrow (i) button displays the Level I Parameters in the following

order:

• Time of Day

• Time of Regeneration

• Hardness

• Salt Amount

• Capacity

If you continue to press the down arrow (i) button, the

parameters start over with Time of Day. Pressing the up arrow (h)

button displays the parameters in reverse order. Refer to Table

1 for a description of these parameters and the available ranges

for each parameter.

SET

h

i



changing, press the left arrow (f) button. When you reach the

far left digit, pressing the left arrow (f) button will return you

to the far right digit.

Note: If you press and hold either the up arrow (h) button

or the down arrow (i) button for more than one second, the

ashing number will increment or decrement at the rate of 10

counts per second.

When the number is correct, press the left arrow (f) button.

The rst number stops ashing and the next number starts

ashing. You can only change the ashing number. Continue

changing numbers until you reach the desired setting. Press

the SET button. The numbers stop ashing and the control

accepts the new setting. After approximately 30 seconds,

the control starts alternating the display between Time of

Day and Capacity.

Note: If a beep sounds, the new setting is not accepted

because it was outside the allowable range. The old value

will be displayed.

Time of Day

Press the SET button. The display will show the Time of

Day with the minutes digit blinking. If you want to change

this number, press the up arrow (h) button to increase the

number or the down arrow (i) button to decrease the number.

To skip the number without changing, press the left arrow (f)

button. The rst number stops ashing and the next number

starts ashing. You can only change the ashing number.

When you have reached the far left digit, pressing the left

arrow (f) button returns you to the far right digit. Continue

changing numbers until you reach the desired setting. Press

the SET button to enter the value.

Time of Regeneration

The next value displayed is the Time of Regeneration. It

has a default value of 2:00 a.m. If this is not acceptable,

press the SET button and change the number. Press the SET

button to enter the value. If 2:00 a.m. is acceptable,

press the down arrow (i) button.

Hardness

Hardness is the next value displayed. This value is

the water hardness expressed in grains per gallon

(milligrams per liter). The default value is

10 grains/gallon (100 mg/L). If this is not acceptable,

press the SET button and enter a new value. Any value

between 3 and 250 grains per gallon (30 and

2500 milligrams per liter) is allowed. Press the SET

button to enter the new value.

Salt Amount

Salt Amount is the next value displayed. The default value

for Salt Amount is 6 pounds (2.7 kilograms) of salt; refer to

Table 2 for suggested salt settings.

Note: 

SET button



i

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 26 27

Commentaires sur ces manuels

Pas de commentaire

AvantaPure 269 Spécifications Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Climatiseurs à système divisé AvantaPure 269