AvantaPure 269 Spécifications télécharger pdf (Page 25)

Problem Possible Cause Solution

6. No water ow display when

water is owing (colon does

not blink).

a. Bypass valve in bypass position.

b. Meter probe disconnected or not fully

connected to meter housing.

c. Restricted meter turbine rotation due to

foreign material in meter !

d. Defective meter probe.

e. Defective circuit board.

a. Shift bypass valve into service position.

b. Fully insert probe into meter housing.

c. Remove meter housing, free up turbine

and ush with clean water. Turbine should

spin freely. If not, refer to the Water Meter

Maintenance section.

d. Replace control.

e. Replace control.

Control

display is

frozen at

Regen Time

Remaining.

a. Back to back regenerations were

requested.

a. Refer to the Manual Regeneration section.

Control

regenerates at

the wrong time

of day.

a. Power outages.

b. Time of day set incorrectly.

c. Time of regeneration set incorrectly.

a. Reset time of day to correct time of day.

b. Reset time of day to correct time of day.

a. Reset time of regeneration.

9. Timer stalled in regeneration

cycle.

a. Motor not operating.

b. Motor runs backwards.

c. No electric power at outlet.

d. Incorrect voltage or frequency (Hz).

e. Broken gear.

f. Defective switch.

g. Air leak in brine connections (pressure

locked apper).

h. Binding of camshaft.

i. Water pressure greater than 125 psi

during regeneration.

j. Defective circuit board.

a. Replace control.

b. Replace control.

c. Repair outlet or use working outlet.

d. Replace timer and/or transformer with one of

correct voltage and frequency (Hz).

e. Replace control.

f. Replace control.

g. Check all junction points and make

appropriate corrections.

h. Remove foreign object obstruction from valve

discs or camshaft.

i. Install pressure regulator to reduce pressure.

j. Replace control.

10. Continuous regeneration.

Camshaft does not stop at

the end of regeneration.

a. Broken projection on drive gear.

b. Defective switch.

a. Replace control.

b. Replace control.

11. Control does not regenerate

automatically or when

REGEN button is depressed.

a. Transformer unplugged.

b. No electric power at outlet.

c. Defective motor.

d. Broken gear.

e. Binding in gear train.

f. Defective switch.

a. Connect power.

b. Repair outlet or use working outlet.

c. Replace control.

d. Replace control.

e. Replace control.

f. Replace control.

12. Control does not regenerate

automatically but does

regenerate when REGEN

button is depressed.

a. If water ow display is not operative,

refer to item 5 in this table.

b. Incorrect hardness and capacity

settings.

c. Defective circuit board.

a. Refer to item 5 in this table.

b. Set new control values. Refer to the

Programming section.

c. Replace control.

13. Run

out of soft

water between

regenerations.

a. Improper regeneration.

b. Fouled resin bed.

c. Incorrect salt setting.

d. Incorrect hardness or capacity settings.

e. Water hardness has increased.

f. Restricted meter turbine rotation due to

foreign material in meter housing !

g. Excessive water usage below 1/5 gallon

per minute.

a. Repeat regeneration making certain that

correct salt dosage is used.

b. Use resin cleaner.

c. Set salt control to proper level. Refer to the

Programming section in this manual.

d. Set to correct values. Refer to the

Programming section in this manual.

e. Set to new value. Refer to the Programming

section in this manual.

f. Remove meter housing, free up turbine, and

ush with clean water. Turbine should spin

freely, if not, replace meter.

g. Repair leaky plumbing and/or xtures.

1 2 ... 20 21 22 23 24 25 26 27

Commentaires sur ces manuels

Pas de commentaire

AvantaPure 269 Spécifications Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Climatiseurs à système divisé AvantaPure 269